Contents - Index

TS-2000 Menu






Menu settings using the keyboard:

For those who would rather use the keyboard for data entry than the mouse, it is possible to do so in the menu:

Use the Up, down, left and right arrow keys to move around the menu.

When you want to change an alphabetic or numerical value, press the <ENTER> key.   Depending on the data, either a drop-down list will appear, or data may be entered as in a text editor.    For the drop-down list, use the up/down arrow keys to scroll through the values.  Enter data into the text editor as you normally would.   A <ENTER> will confirm the change.

For the selections with buttons,  use the space bar to step among the choices. 

For the DTMF editor, a button will pop up when you press return on the data fields.  The buttons spans both A and B fields.   When the button pops up, press the spacebar to click the button, and the DTMF Editor will pop up.   Use the arrow keys to navigate around the DTMF editor, and close it when through editing.

Items 55, 61A, 61E and 62E.  Are not included in the menu because changing one of these settings while downloading can affect the TS-2000's serial port ( e.g. Turning on the TNC will cause the port to go into packet mode, and not respond to data communications ).  

Note that Item 5's default is dependent on which version of the TS-2000 you have.   To change the default in link700, click on Preferences/Menu and set the "TS-2000 Menu Item Default" to the value that corresponds to your radio (  ON for E types, OFF for K types ) 

The menu functions are listed below:

      Menu No. Function    Possible Settings
00 Display brightness   OFF,1,2,3,4
01 Key illumination    ON/OFF
02 Tuning control change per revolution 500,1000
03 Tuning with the MULTI/CH control  ONOFF
04 Rounds off VFO frequencies changed ON/OFF
  by using the MULTI/CH control  ON/OFF 
05 9 kHz frequency step size for the 
  MULTI/CH control in AM mode on the 
  AM broadcast band 
06A Memory-VFO split operation  ON/OFF
06B Tunable(ON) or fixed (OFF) memory  ON/OFF
  channel frequencies 
07 Program scan partially slowed  ON/OFF
08 Slow down frequency range for the  100,200,300,400,500
  Program scan 
09 Program scan hold   ON/OFF
10 Scan resume method   CO,TO
11 Visual scan range   31,61,91,181
12 Beep output level   OFF,1,2,3,4,5,6,7,8,9
13 TX sidetone volume   OFF,1,2,3,4,5,6,7,8,9
14 DRU-3A playback volume  OFF,1,2,3,4,5,6,7,8,9
15 VS-3 playback volume   OFF,1,2,3,4,5,6,7,8,9
16 Audio output configuration for   0,1,2
  EXT.SP2 or headphone 
17 Reverses the EXT.SP1 and EXT.SP2 ON/OFF 
  ( the headphone jack L/R channels )
  audio outputs 
18 Enable an input from the HF RX ANT  ON/OFF
  connector 
19A S-meter squelch    ON/OFF
19B Hang time for S-meter squelch  OFF,125,250,500
20 DSP RX equalizer   OFF, H BOOST,F PASS, B BOOST,CONVEN,USER
21 DSP TX equalizer   OFF, H BOOST,F PASS, B BOOST,CONVEN,USER
22 DSP TX filter bandwidth for SSB or AM 2.0,2.2,2.4,2.6,2.8,3.0
23 Fine transmit power tuning  ON/OFF
24 Time-out Timer    OFF,3,5,10,20,30
25 Transverter frequency display  ON/OFF
26 TX hold when AT completes the tuning ON/OFF
27 In-line AT while receiving   ON/OFF
28A Linear amplifier control delay for   OFF,1,2
  HF band 
28B Linear amplifier control delay for   OFF,1,2
  50MHz band 
28C Linear amplifier control delay for   OFF,1,2
  144MHz band 
28D Linear amplifier control delay for   OFF,1,2
  430(440)MHz band 
28E Linear amplifier control delay for   OFF,1,2
  1.2GHz band 
29A Repeat the playback   ON/OFF
29B Interval time for repeating the playback 0,1,2,3,4..60 ( in steps of 1 sec )
30 Keying priority over playback  ON/OFF
31 CW RX pitch/TX sidetone frequency 400 to 1000 Hz in steps of 50 Hz
32 CW rise time    1,2,4,6
33 CW keying dot/dash weight ratio  AUTO 2.5,2.6,2.7,2.8,2.9,3.0,3.1,3.2,3.3..4.0 ( in steps of 0.1 )
34 Reverse CW keying auto weight ratio ON/OFF
35 Bug key function   ON/OFF
36 Auto CW TX in SSB mode  ON/OFF
37 Frequency correction when changing  ON/OFF
  from SSB to CW 
38 FSK shift    170,200,425,850 (Hz)
39 FSK keying polarity   NORMAL/INVERSE
40 FSK tone frequency   2125,1275
41 Mic gain for FM     LOW,MID,HIGH 
42 Sub-tone mode for FM   BURST,CONT
43 Auto repeater offset   ON/OFF
44 TX hold:1750Hz tone   ON/OFF
45A DTMF number memory select  See the parameter comments.
45B TX speed for stored DTMF number SLOW,FAST
45C Pause duration for stored DTMF number 100,250 ms
45D Enable Mic remote control  ON/OFF
46 MAIN/SUB band:Internal TNC  MAIN,SUB
47 Data transfer speed: Internal TNC 1200,9600 bps
48 DCD sensing band   TNC BAND, MAIN-&SUB
49A Packet Cluster Tune mode  AUTO,MANUAL
49B Packet Cluster RX confirmation tone OFF,MORSE,VOICE
50A Packet filter bandwidth   ON/OFF
50B AF input level for Packet   0,1
50C MAIN band AF output level for packet  0,1
  operation 
50D SUB band AF output level for packet   0,1
  operation
50E MAIN/SUB band: External TNC  MAIN,SUB
50F Data transfer speed: External TNC 1200,9600 bps

51A Front panel PF key   00~99(2-digit),
       0..62:Menu No.,  63: VOICE1 ,  64: VOICE2,  
       65: RX MONI,   66: DSP MONI,  67: QUICK MEMO MR,
       68: QUICK MEMO M.IN, 69: SPLIT,     70: TF-SET, 
       71: A/B,   72: VFO/M  73: A=B, 
       74: SCAN,   75: M>VFO,   76: M.IN,  
       77 CW TUNE,   78: CH 1,   79: CH 2, 
       80: CH 3,   81: FINE,   82: CLR, 
       83: CALL,   84: CTRL,   85: 1MHz, 
       87: NB,   88: N.R.,  89: B.C., 
       90: A.N.,  99: No function,
       All menu numbers may not be available (  depending on the market code ).

51B Microphone PF 1 key   Same as 51A
51C Microphone PF 2 key   Same as 51A
51D Microphone PF 3 key   Same as 51A
51E Microphone PF 4 key   Same as 51A
52 Split frequency transfer in master/slave ON/OFF
  operation 
53 Permit to write the transferred Split  ON/OFF
  frequencies to the target VFOs. 
54 TX inhibit    ON/OFF
55 Packet communication mode  ON/OFF
56 COM port communication speed  4800,9600 bps
57 APO ( Auto Power Off ) function  OFF,60
58 RC-2000 font in easy operation mode FONT-1,FONT-2
59 RC-2000 panel/TS-2000(X) dot-matrix  1,2
  display contrast 
60 Display mode for RC-2000  NEGATIVE,POSITIVE
61A Repeater mode select   OFF,LOCKED,CROSS
61B Repeater TX hold   ON/OFF
61C Remote control ID code   000..999( 3-digit number )
61D Acknowledgment signal in external ON/OFF
  remote control Mode 
61E External remote control   ON/OFF
62A Commander call sign for Sky   A maximum of 9 characters. See page 83.
  Command II+ 
62B Transporter call sign for Sky   A maximum of 9 characters. See page 83.
  Command II+ 
62C Sky Command II+ tone frequency See page 35 for the tone number.
62D Sky Command II+ communication speed 1200,9600 bps
62E Sky Command II+ mode   OFF,CLIENT,COMMAND,TRANSPORTER